Lotus of the week. This auction is for the 12″ Lotus Dragon handguard. This handguard has a custom Cerakote. Airbrushed Titanium with Sig Pink cut edges. The airbrushed Sig Pink shows the detail of the Dragon flys and lady skulls with bows.
Auction 12″ Unique-ARs Lotus Dragon
Lotus of the week. This auction is for the 12″ Lotus Dragon handguard. This handguard has a custom Cerakote. Airbrushed Titanium with Sig Pink cut edges. The airbrushed Sig Pink shows the detail of the Dragon flys and lady skulls with bows. Handguards retail price is $320.
Item condition: New
-constructed of 6061 t6 aluminum
-coated with CeraKote
-includes proprietary mounting system
-fits any mil-spec 556 upper receiver or (dpms style) 308 upper
-pre-drilled and tapped full length for tac rail on top and bottom
-pre-drilled and tapped for tac rail on sides if design allows
Unique-ARs provides a lifetime limited warranty on all free float forends and tac rail. We warranty all materials and finishes will be free from defect. We want you to be more then satisfied with your precision parts and our customer service. We will do our best to make your experience dealing with our company a positive one, however we do not cover stripped or abused parts. Give us a call if you have any questions 888.982.8386.
All stock items can be returned if the Item shows no signs of wear or installation and can be resold as new a refund will be issued. We do not offer refunds on custom work including custom or upgraded paint options. A partial refund will be given on stock items with custom paint if the item can be resold as new.
For a full color chart please visit: http://www.cerakoteguncoatings.com/finishes/?tab=coatings&cat=HSERIES *Please Note: Every effort has been made to accurately represent the colors shown in this catalog. Colors may vary upon lighting conditions. Due to limitations of the printing process, photographic and printed images may not represent true color.
We get asked all the time if our hand guards will work on your AirSoft gun. The Answer is YES, if your AirSoft gun has a standard mill spec threaded upper, which lots do. The standard is 1.250″ x 18 tpi. If you have any questions please shoot us an email.
Mounting Instructions and Tips:
Step: 1) Once you have the old free float-tube and/or barrel nut removed, clean any grease or oil from the threads of the upper receiver extension.
Step: 2) Apply a drop or two of blue LocTite® to the receiver threads and screw the large aluminum barrel-nut on until it stops, then back it off until the gas tube holes line up.
Step: 3) Insert the barrel and slide the steel castle bolt over the barrel and thread it into the aluminum barrel-nut; now, use a punch to to keep the gas tube holes aligned .
Step 4) With the punch inserted in the gas tube holes turn the steel castle bolt by hand until you get a good, solid hand-tight alignment with the barrel-nut and receiver. Once you have the two aligned, let it set for a 2-24 hours ; after the blue LocTite® has cured between the barrel-nut and receiver, the steel insert and barrel can be removed.
Step 5) For final assembly insert the barrel, thread the steel castle bolt into the barrel-nut and once it is finger tight, back it off three or four turns and place a drop of blue LocTite® on the threads of the steel insert, right where it becomes visible out of the barrel-nut.
Step 6) Now torque the steel insert down to desired torque. This can all be accomplished with or without the use of punch in the gas tube but the barrel-nut can move while you are torquing the steel castle nut, and then you will have to loosen it up and re-time it. We recommend using the punch to insure proper timing.
Step 7) Once you have installed the gas tube, slide the handguard onto the barrel nut and aligned the 6 radial holes with the corresponding holes in the barrel-nut, the 6 countersunk screws can be installed. For 308 barrel nuts it is important that screws are installed in the proper location TOP,MIDDLE, BOTTOM Inserting screws into the wrong hole will damage the barrel nut. Tighten until snug. DO NOT over tighten. Stripped screws are not covered by the warranty.